[Motherboard] Troubleshooting — Cannot find the hard disk drive or SSD(M.2) after motherboard powers on
Scan QR code to open this page with your smart phone.
[Motherboard] Troubleshooting — Cannot find the hard disk drive or SSD(M.2) after motherboard powers on
To provide you more detailed instruction, you can also click ASUS Youtube video link below to know more about cannot find the hard disk drive or SSD(M.2) after motherboard powers on
If the computer can't detect and find hard disk or SSD after the power is turned on, please follow the steps below to troubleshoot:
A. Confirm the settings in BIOS
1. Please try to update the latest version BIOS from ASUS official website. Please refer to this FAQ for more : [Motherboard] ASUS EZ Flash 3 — Introduction
2. After the computer powers on, please immediately press 'delete' key on the keyboard to enter EZ Mode. Please confirm the information of the connected hard disk or SSD in Storage Information (Ex: PRIME B550-PLUS)
(If the computer enters BIOS Advance Mode after you press 'delete', you can press 'F7' again to enter EZ Mode)
Note：For the old models (ex: TUF B450-PLUS GAMING) ,which use PCIE Mode M.2 SSD(including: NVME M.2), information of hard disk or SSD doesn't show in Storage Information in BIOS EZ Mode due to the framework of the BIOS. This phenomenon is normal, please be noted.
3. Please enable [CSM] in BIOS
a. After the computer powers on, please press 'delete' to enter EZ Mode, and then press 'F7' to enter Advanced Mode as below:
b. Click [Boot] — [Launch CSM]. Please set [Launch CSM] as [Enabled] as below:
c. Press 'F10' to save the BIOS setting, and click [OK] to reboot. Confirm whether the computer can recognize the hard disk or SSD
4. If you have set CPU overclocking or Memory overclocking, the computer may not detect the hard disk or SSD due to overclocking instability. Please set BIOS to the default setting by the below steps:
a. After the computer powers on, please immediately press 'delete' key on the keyboard to enter EZ Mode (you can refer to the picture in step 2)
b. Press 'F5' to set the BIOS to default setting, then press 'F10' to save BIOS setting and click [OK] to reboot. Confirm whether the computer can detect the hard disk or SSD.
5. If the computer still can't detect the hard disk or SSD after you followed the above step 1
4, please confirm the hardware by below steps
B. Confirm the hardware
1. Please try to replug Sata cable on the motherboard, and confirm Sata cable is correctly connected.
2. Please try to replug Sata cable or power cable on the hard disk or SSD. Confirm Sata cable or power cable is correctly connected
3. Please try another SATA port of the power supply
4. Please replace with a good Sata cable without problem
5. Please try to connect hard disk or SSD to anther Sata port of the motherboard
6. Please replace with another power supply, and confirm whether the Sata cable of the power supply is abnormal
7. If the connected SSD is M.2 SSD, please try to replug M.2 SSD. Confirm M.2 SSD is correctly connected and the M.2 screw is locked, as below:
8. Please check user manual on ASUS Official Website. Confirm whether M.2 port supports ① , and confirm whether it is shared ② with other port
① M.2_1 port can support SATA mode and PCIE mode
M.2_2 port can only support PCIE mode and can't support SATA mode. Therefore, if you connect SATA mode M.2 SSD to M.2_2 port, the computer can't recognize.
② M.2_1 port is shared with SATA6G_1 port. Therefore ,when connecting the device to the two ports, SATA6G_1 port will be closed.
At this time, the computer can only recognize M.2 SSD in M.2_1 port, and it can't recognize the hard disk in SATA6G_1. If you need computer to recognize the hard disk in SATA6G_1，please connect Sata cable of SATA6G_1 port to other Sata port, such as SATA6G_3 or SATA6G_4
9. If you still can't solve your problem with the above steps, the hard disk may have the physical damage or the SSD is damaged. Please try to replace with a properly working hard disk or SSD.
If the problem still cannot be fixed, please contact ASUS Porduct Support.
Включаем поддержку NVMe на старых материнках на примере Asus P9X79 WS
Привет Хабр! В голову мне закралась мысль, и я ее думаю. И придумал. Все дело в жуткой несправедливости производителя, которому абсолютно ничего не стоило добавить модули в UEFI Bios для поддержки загрузки с NVMe через переходники на материнках без слота m.2 (что, к стати, без вопросов реализовано китайцами на материнках HuananZhi). Неужели не возможно — подумал я и стал копать. Нарыл кучу нерабочих советов, пару раз окирпичил материнку, но я добился своего. В этой статье я почерпнул львиную долю полезной информации. Но и тут достаточно много подводных камней. Например совершенно не ясно в какой индекс записывать модули. Итак, начнем модифицировать наш биос. Внимание! Данный материал применим ТОЛЬКО к AMI Aptio Bios и ни к одному другому, так что если у вас не оно — смело проходите мимо.
Для начала скачаем инструменты. Распаковав в удобную папку скачаем биос от ближайшей модели с поддержкой NVMe (Для P9X79 это Sabertooth X99) и оригинальный биос для нашей материнки. Кладем скаченные биос в папку с инструментами, запускаем MMTool и открываем биос с поддержкой NVMe:
Затем идем на вкладку Extract, находим и извлекаем нужные нам модули (NvmeInt13, Nvme, NvmeSmm), имена набираем идентичные с расширением .ffs и жмем Extract, опции оставляем «As is»:
Когда все модули извлечены, открываетм командную строку от администратора и идем в папку с инструментами\AFUWINx64
Там снимаем дамп:
Переходим к MMtool и открываем наш дамп.
Переходим на вкладку Insert и ОБЯЗАТЕЛЬНО кликаем в поле на индекс 02 (для разных материнок индексы могут отличаться, смотрите на индекс, в котором изначально лежали модули NVMe и сравнивайте содержимое с целевым Bios).
Далее жмем Browse и находим наши извлеченные модули:
Нажимаем Insert (опция «As is») и повторяем действие для остальных модулей, соблюдая порядок, как в биос с поддержкой NVMe (У меня NvmeInt13, Nvme, NvmeSmm). Затем находим наши новые модули в списке дабы убедится что все они на месте и в правильном порядке:
Жмем Save Image As и сохраняем модифицированный биос в папку AFUWINx64. В ту же папку помещаем оригинальный биос нашей материнки и приступаем к прошивке. Сначала шьем оригинальный биос, дабы обойти защиту:
Затем шьем наш модифицированный:
Соответственно имена файлов подставляем свои. После перезагрузки наш биос будет уметь загружаться с NVMe.
После обновления биос вы обнаружите кучу устройств с восклицательным знаком в диспетчере. Лечится это просто: скачайте драйвер чипсета от материнской платы-донора модулей и установите их на целевой машине.
ВСЕ ДЕЙСТВИЯ ВЫ ПРОДЕЛЫВАЕТЕ НА СВОЙ СТРАХ И РИСК, АВТОР МАТЕРИАЛА НИКАКОЙ
ОТВЕТСТВЕННОСТИ НЕ НЕСЕТ!
How to Enable M.2 SSD on ASUS ROG Z390 Motherboard
You recently purchased the latest NVME M.2 SSD drive and use it as your primary storage drive for your OS. Surprisingly, when you try to install Windows 10 on it there is a problem stopping you from installing it, the M.2 drive is not listed on the drive list. An error message saying “No drives were found. Click Load Driver to provide a mass storage driver for installation”.
This problem occurs because of the lacked of signed UEFI driver for PCIE-based storage like the NVME M.2 SSD due to latest Microsoft Secure Boot regulations. Resetting your motherboard settings to default will not work, the only way work around with it is to enable something on your BOOT settings of your ASUS ROG Z390 motherboard.
Table of Contents
Removed SATA drives
First of all, you have to remove all connected SATA storage drive from your computer. This is to make sure that there is no conflicting UEFI and non-UEFI storage drive that blocking you from installing an OS.
You can physically removed it from your motherboard or via BOOT menu (See instruction below if you have no idea how to enter BIOS, key is F1 or DEL).
At your BIOS settings, go to Advanced > SATA/Storage Configuration. Then disabled all of the SATA_1 up to 6 slots at the settings.
Enable Launch CSM
Once all SATA drives are disconnected. Make sure your M.2 NVME is connected to your motherboard. It is best to place it on the upper slot if you have two M.2 slots.
To enable the Compatibility Support Modules (CSM), you need to go to your BIOS (See instruction below for entering to BIOS).
Switch to Advanced if you’re in Easy Mode.
Then at the Boot tab, browse at the 3rd selection which is the CSM (Compatibility Support Module).
Then, set the Launch CSM to Enable.
The default values for further settings is as follow:
- Boot Device Control – UEFI and Legacy OPROM
- Boot from Network Devices – Legacy only
- Boot from Storage Devices – Legacy only
- Boot from PCI-E/PCI Expansion Devices – Legacy only
To apply the changes, go to Exit tab and select the Save Changes and Exit. This will boot your computer and once you’re in the Windows 10 installation you should now see the drive for your M.2 SSD.
How to go to BIOS in ASUS ROG Z390
To go to the BIOS menu of your motherboard, simply turn off your computer first. Then turn it on, while turning on, you need to press either F1 or DELETE key from your keyboard repeatedly. Once you are in the BIOS, stop pressing.
Как включить м2 в биос asus
How to enable m2 in bios Asus? Easy Fix Now
If your Asus computer has an M.2 slot on the motherboard, you can install a solid-state drive (SSD) to boost the system’s speed and increase its storage capacity. To do this, you’ll need to enable the > M.2 slot in the BIOS settings first. Here’s how:
1. Reboot your Asus computer and > press the “F2” key repeatedly when the ASUS logo appears on the screen during bootup to enter BIOS Setup Utility.
2. Go to the “Advanced” tab and select “Onboard Devices Configuration.”
3 . Find the “M 2 Enable” option under the SATA Configuration section, and set it as > “Enabled.” Press the F10 key to save changes and exit from BIOS Setup Utility.
M.2 not showing up in bios Asus
If your m.2 drive isn’t showing up in the BIOS, you can check a few things:
- Make sure that the driver is correctly seated in the slot. If it’s not, try removing and reinserting it.
- Check your BIOS settings to see if the m.2 drive is enabled. If not, enable it and save your changes before restarting your computer.
- You may need to update your BIOS to the latest version if all else fails to get support.
How do I get my m 2 to work?
There are a few things you can attempt to get your unresponsive m.2 SSD up and running. To begin with, see if the m.2 slot is enabled by consulting the motherboard instructions. If it is, try reseating the SSD and making sure it is connected properly. If that doesn’t work, you might try installing the most recent motherboard chipset drivers or updating your BIOS. Unfortunately, your m.2 SSD is probably malfunctioning and will need to be replaced if none of those fix work.
How do I make my M2 boot drive?
If you’re looking to improve your computer’s performance, making your M2 boot drive bootable is one way to do it. This can be done quickly with a few simple steps. First, identify which type of M2 drive you have – there are two different types, SATA and NVMe. Download the appropriate drivers from the manufacturer’s website.
Final thought
Enabling M.2 in BIOS on an Asus motherboard can be easily accomplished by accessing the BIOS settings during startup, navigating to the Advanced menu, and selecting the Onboard Devices Configuration option. From there, ensure the M.2 Configuration setting is enabled and save the changes before restarting your computer. By enabling M.2 in BIOS, you can take advantage of the benefits of this high-speed storage technology, such as faster boot times and improved overall performance. As always, it’s important to consult the manual or Asus support website for specific instructions and exercise caution when changing your BIOS settings.